Bambu Lab A1 mini
Bambu Lab A1 mini against 295 PETG products: 47 fit, 203 cannot reach the full recommended range, 3 cannot print this material at a recommended temperature, and 42 are missing an essential check. Manufacturer page checked 14 October 2026.
| Filament | Result | Why | Buy |
|---|---|---|---|
| Amolen PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Anycubic PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Anycubic Translucent PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Bambu Lab PETG Basic | — | Nozzle temperature is not in our current sources. | |
| Bambu Lab PETG HF | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Bambu Lab PETG Matte | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Bambu Lab PETG Translucent | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Bambu Lab PETG-CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| colorFabb PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Creality CR-PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Creality Hyper PETG | — | Nozzle temperature is not in our current sources. | |
| Creality PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Creality Soleyin Basic PETG | — | Bed temperature is not in our current sources. | |
| ELEGOO PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ELEGOO PETG PRO | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| ELEGOO PETG Translucent | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| ELEGOO PETG-CF | Partial | This filament is carbon-fiber, glass-fiber, or glow-in-the-dark, so a hardened nozzle is the upgrade to check. The stock nozzle is not hardened. | |
| ELEGOO PETG-GF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| ELEGOO RAPID PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Eryone PETG | — | Nozzle temperature is not in our current sources. | |
| Eryone PETG-CF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| eSUN 3D ESUN PETG Matte | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| eSUN 3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| eSUN 3D PETG-Basic | — | Nozzle temperature is not in our current sources. | |
| eSUN 3D PETG-Matte | — | Nozzle temperature is not in our current sources. | |
| eSUN 3D PETG+CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| eSUN 3D PETG+HS | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| eSUN 3D Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| extrudr Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| extrudr PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Hatchbox PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Inland PETG+ | — | Nozzle temperature is not in our current sources. | |
| JAYO PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Kingroon High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Kingroon PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Kingroon PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Overture High Speed PETG Refill | — | Nozzle temperature is not in our current sources. | |
| Overture PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Overture PETG Basic | — | Nozzle temperature is not in our current sources. | |
| Overture PETG Refill | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Polymaker PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Polymaker PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Polymaker Polylite PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Polymaker Polymax PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Protopasta Glitter PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Protopasta Metallic PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Protopasta PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Protopasta PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Protopasta Recycled PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Protopasta Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Protopasta Simply PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Protopasta Static Dissipative PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Protopasta Translucent PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Prusament Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Prusament PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Prusament PETG CF | Partial | The listed bed range reaches 100 °C (212 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 80 °C (176 °F), is within that maximum. | |
| Prusament PETG Magnetite | — | Nozzle temperature is not in our current sources. | |
| Prusament PETG Tungsten | — | Nozzle temperature is not in our current sources. | |
| Prusament PETG V0 | — | Nozzle temperature is not in our current sources. | |
| Siraya Tech Fibreheart PETG-CF Pro | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| SUNLU Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU High Speed Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU Luminous Glow In The Dark PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU Matte PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SUNLU PETG 2.0 | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| SUNLU PETG Carbon Fiber | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| SUNLU PETG Glow In The Dark Filament | Partial | This filament is carbon-fiber, glass-fiber, or glow-in-the-dark, so a hardened nozzle is the upgrade to check. The stock nozzle is not hardened. | |
| 3D Fuel Pro PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3D Printing Canada Budget PETG | — | Nozzle temperature is not in our current sources. | |
| 3DE Premium | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| 3DEA PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 75 °C (167 °F), is within that maximum. | |
| 3DEA PETG Translucent | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 75 °C (167 °F), is within that maximum. | |
| 3DJAKE Easy Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DJAKE easy PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DJAKE Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DJAKE PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DO PETG | — | Nozzle temperature is not in our current sources. | |
| 3DPower Basic PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DPower Hyper Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DPower PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DPower Select PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DXTech PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DXTech PETG 3DXStat EMI | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DXTech PETG 3DXStat ESD | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| 3DXTech PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Add-North ESD PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Add-North Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Add-North PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Add-North PETG Economy | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Add-North PETG Flame Retardant V0 | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Add-North PETG Koltron G1 | — | Bed temperature is not in our current sources. | |
| Add-North PETG PRO Matte | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Add-North PETG Rigid X | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| Add-North rPETG Matte | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Alzament PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Alzament PETG Hyper | — | Nozzle temperature is not in our current sources. | |
| Alzament PETG-CF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| Ambrosia PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| ATARAXIA ART PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Atomic Filament PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Atomic Filament PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| AURAPOL ARMY PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| AURAPOL PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| AzureFilm PETG | — | Nozzle temperature is not in our current sources. | |
| Buddy3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| CC3D Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| CC3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| CC3D PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| CHCKX PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Cookiecad PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Dancyn 3D Prints PETG HF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Das Filament PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Devil Design Galaxy PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Devil Design PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Dremel Digilab PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Dremel PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| EasyPrint PETG | — | Nozzle temperature is not in our current sources. | |
| EconoFil PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| EconoFil PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Eolas Prints PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| EPAX High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy Easy PET-G | — | Nozzle temperature is not in our current sources. | |
| Fiberlogy Easy PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy Matt PET G Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy PET-G | — | Nozzle temperature is not in our current sources. | |
| Fiberlogy PET-G ESD | Outside limits | The listed bed temperature starts at 85 °C (185 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot print this material at the recommended bed temperature. | |
| Fiberlogy PET-G V0 PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Fiberlogy Refill Easy PET-G | — | Nozzle temperature is not in our current sources. | |
| Fiberon PETG-ESD | — | Nozzle temperature is not in our current sources. | |
| Fiberon PETG-rCF08 | — | Nozzle temperature is not in our current sources. | |
| FilamentPM ESD PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 80 °C (176 °F), is within that maximum. | |
| FilamentPM PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FilamentPM PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FilamentPM Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Filamentree PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Filamentree PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Filamentworld Metallic Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Filamentworld PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Filkemp PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE Chameleon PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE Metallic Rapid Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE Rapid PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FLASHFORGE Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FormFutura Bulk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 80 °C (176 °F), is within that maximum. | |
| FormFutura CarbonFil | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FormFutura CarbonFil CF03 | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| FormFutura EasyFil ePETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FormFutura Hdglass | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 80 °C (176 °F), is within that maximum. | |
| FormFutura PETG CarbonFil | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| FormFutura PETG Hdglass | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 80 °C (176 °F), is within that maximum. | |
| FormFutura Premium PETG Flame Retardant | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| FormFutura ReFill PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Francofil PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Francofil PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Geeetech PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Gizmo Dorks PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| GST3D PETG | — | Nozzle temperature is not in our current sources. | |
| GST3D PETG translucent | — | Nozzle temperature is not in our current sources. | |
| GST3D PETG-CF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| iBOSS 3D Light Gray | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| IC3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| IC3D PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| IC3D Recycled Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| IEMAI CF-PETG | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| IEMAI PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Insignia PETG | — | Nozzle temperature is not in our current sources. | |
| Inslogic PETG CF10 | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Inslogic PETG Pro | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| iSangHu High Speed Translucent PETG | — | Nozzle temperature is not in our current sources. | |
| iSANMATE PETG Clear Glitter | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| iSANMATE pink | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Kimya PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| KiwiFil PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| KiwiFil PETG Rainbow "Dark Green Ocean" | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| KiwiFil PETG Rainbow "Dark Purple Galaxy" | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| L3D PETG | — | Nozzle temperature is not in our current sources. | |
| Matter3D Inc Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Matter3D Inc PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Matter3D Inc PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| MatterHackers PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Nebula PETG Art Chameleon | — | Nozzle temperature is not in our current sources. | |
| Nebula PETG Premium | — | Nozzle temperature is not in our current sources. | |
| Nobufil Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Nobufil Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Nobufil PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Nobufil PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Paramount 3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Paramount 3D PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Patron EG PETG HS | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 75 °C (167 °F), is within that maximum. | |
| Polar Filament PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PolyLite PETG | — | Nozzle temperature is not in our current sources. | |
| PolyLite Translucent PETG | — | Nozzle temperature is not in our current sources. | |
| PrimaCreator Easyprint PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrimaCreator PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrimaCreator Primaselect PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrimaCreator Primavalue PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrimaSelect PETG CARBON | Partial | This filament is carbon-fiber, glass-fiber, or glow-in-the-dark, so a hardened nozzle is the upgrade to check. The stock nozzle is not hardened. | |
| PrimaSelect Solid PETG | — | Nozzle temperature is not in our current sources. | |
| Print With Smile Bicolor Metallic PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Print With Smile PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Print With Smile PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Print With Smile RE PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrintedSolid Jessie Premium PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrintedSolid PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| PrintedSolid PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Professional LAB PETG | — | Nozzle temperature is not in our current sources. | |
| Professional LAB PETG Matte | Partial | The listed bed range reaches 85 °C (185 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 75 °C (167 °F), is within that maximum. | |
| Professional LAB PETG Transparent | — | Nozzle temperature is not in our current sources. | |
| Professional LAB PETG-CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 60 °C (140 °F), is within that maximum. | |
| Prografen PETG Graphene Light | — | Nozzle temperature is not in our current sources. | |
| Prografen PETG Graphene Strong | — | Nozzle temperature is not in our current sources. | |
| Proteor Print PETG | Outside limits | The listed bed temperature starts at 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot print this material at the recommended bed temperature. | |
| Push Plastic PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Push Plastic PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| QIDI Tech PETG Basic | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| QIDI Tech PETG Rapido | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| QIDI Tech PETG Translucent | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| QIDI Tech PETG-CF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| QIDI Tech PETG-GF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| QIDI Tech PETG-Tough | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Recreus PET G Hf High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Recreus PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Recreus PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| RecyclingFabrik PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Renkforce PETG | — | Bed temperature is not in our current sources. | |
| ROSA3D Filaments High Speed Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments Matte PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments Pet G Galaxy Hs PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments Pet G Hs PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments Pet G Structure Hs PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments PET-G MDT | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments PET-G Standard Neon Green Glow in the Dark | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| ROSA3D Filaments PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SainSmart Glossy Gt 3 Silk High Speed PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SainSmart Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SainSmart PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SainSmart PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SainSmart Silk PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Sakata 3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Sakata 3D PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Slic3D PETG Basic | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| SMART MATERIALS 3D PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SMART MATERIALS 3D PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| SmartPrint PETG | — | Nozzle temperature is not in our current sources. | |
| SmartPrint PETG Transparent | — | Nozzle temperature is not in our current sources. | |
| Snapmaker PETG | — | Nozzle temperature is not in our current sources. | |
| Snapmaker PETG HF | — | Nozzle temperature is not in our current sources. | |
| Spectrum Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PET G Matt Matte PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PET-G FR V0 PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PET-G Glitter PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PET-G Premium PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PETG Carbon | Partial | This filament is carbon-fiber, glass-fiber, or glow-in-the-dark, so a hardened nozzle is the upgrade to check. The stock nozzle is not hardened. | |
| Spectrum PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Spectrum PETG FR V0 | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PETG FX120 | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PETG Glitter | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PETG Glow in the Dark | Partial | This filament is carbon-fiber, glass-fiber, or glow-in-the-dark, so a hardened nozzle is the upgrade to check. The stock nozzle is not hardened. | |
| Spectrum PETG HT100 | Outside limits | The listed bed temperature starts at 100 °C (212 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot print this material at the recommended bed temperature. | |
| Spectrum PETG MATT | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PETG Premium | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PETG Premium High Speed | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum PTFE | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Spectrum R PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| TECBEARS Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TECBEARS PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Tectonic 3D Aura PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TEQStone PETG | Partial | The listed bed range reaches 100 °C (212 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 60 °C (140 °F), is within that maximum. | |
| The Filament PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| The Filament PETG CF | Partial | This filament is recorded as needing a hardened nozzle. The stock nozzle is not hardened. | |
| The Filament PETG Lite | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| TINMORRY Frosted GF PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY Galaxy PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY Glow PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY Marble PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY Metallic PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| TINMORRY Rapid-Eco PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Verbatim PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Voxel PLA PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Winkle PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| Winkle PETG CF | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. | |
| XZN PETG | Fits | A1 mini can reach the listed nozzle and bed. Recorded enclosure and nozzle checks do not block it. | |
| Zyltech PETG | Partial | The listed bed range reaches 90 °C (194 °F), above this printer's maximum of 80 °C (176 °F). This printer cannot reach the full recommended range. The low end, 70 °C (158 °F), is within that maximum. |
FilamentFacts may earn a commission when you buy through links on this page. As an Amazon Associate we earn from qualifying purchases.
Bambu Lab A1 mini against 295 PETG products: 47 fit, 203 cannot reach the full recommended range, 3 cannot print this material at a recommended temperature, and 42 are missing an essential check. Manufacturer page checked 14 October 2026.
Fits means the nozzle, bed, and enclosure checks all pass. Partial means the printer can print at the low end of a range but cannot reach the full recommended range, or the stock nozzle is not hardened. Outside limits means a recommended temperature starts above the printer maximum. A missing essential check is not a fit.
0 in the tray
Compare